White powder polymer Quick setting ACRY-POWDER 35gr

White powder polymer ACRY-POWDER quick setting by Mesauda Milano . It is a polymer powder to be mixed with the Acrylic-Liquid monomer in order to build acrylic nails. Quick set. Air dry. Available in 3 colors.

Application
To prepare the nail:
1 - Disinfect the client's hand with the disinfectant solution.
2 - Push back the cuticles with the cuticle pusher.
3 - Clean carefully around the cuticles, removing all residues.
4 - Carefully polish the entire surface of the nail plate with a white block.
5 - Carefully remove all dust produced with a suitable brush.
6 - Apply a layer of Nail Prep and let air dry for about 10 seconds.
7 - Apply a coat of Ultrabond and allow to air dry for about 30 seconds. Leave the sticky layer produced after drying.

To prepare the brush
1 - Pour a small amount of monomer into the cup.
2 - Prepare the brush by immersing it in the monomer to wet the bristles and remove any air that may be trapped, which could create bubbles in the final result.
3 - Wipe the brush on the appropriate placemat.

To create a pearl
1 - Dip the brush in the monomer and wipe off the excess liquid with the side of the Dappen dish.
2 - Touch the tip of the brush in the powder to create the bead of the desired size.
3 - Let the monomer saturate the powder. The pearl should be medium in size and have a round, smooth and satin finish.

To create the extension with a nail shape
1 - Place a pearl of white (Acry-Powder White) in the middle of a nail shape of what will become the nail extension.
2 - Start pushing the product towards the natural free edge, working it towards the sides of the “smile line”.
3 - Lightly brush the product and pat it side to side to create the width, length and thickness of the extension edge.
4 - View the nail from different angles to make sure the extension is uniform over the natural nail.
5 - Define the shape of the "smile line" by using the tip of the brush in a tip and pushing along the back part of the "smile line" to place the product in place. This will create a lip that will act as a barrier preventing the Pink Acry-Powder from being dragged onto the "smile line".

Far end overlap
1 - Take a medium size pearl of transparent powder (transparent acrylic powder) or pink (acrylic acrylic powder) and place it in the center of the nail plate.
2 - Gently tap the product, moving it along the cuticles, taking care not to touch the skin.
3 - Pluck the remaining product towards the free edge.
4 - Press the bead to flatten and tap to smooth the product.
5 - Pluck with the extension of the nail and cover the point. Continue like this until the entire section is covered and smooth.
6 - Place another bead in the middle of the nail slightly above the smile line. This area will be the highest point of the finished nail and will provide additional support in this stress area.
7 - Flatten the brush and work the product from side to side.
8 - Work the product up to the smile line, without going beyond it, and spread the polymer on the free edge.
9 - View the nail from different angles to ensure that the application is uniform compared to the natural nail.

Finishing
1 - Let the product harden completely in air then file the nails to the desired shape.
2 - File along the side walls of each nail, taking care to align the cuticle and the free edge.
3 - File the cuticles by making rounded movements and going towards the center of the nail. Make sure the nails are thin, even, and consistent. Note the product should be applied thinly around the cuticle to avoid lifting.
4 - Polish the nails to get an ultra shiny finish or apply Xtreme Shine and cure in a UV / LED lamp (36 Watt) for 4 min / 2 min to finish the job. If using a lower wattage source, cure for an additional 1-2 minutes.

Warnings: Do not expose the product to excessive light or sources of heat. Avoid contact with skin as the product may irritate. In the event of allergic reactions, discontinue use. Harmful if inhaled or swallowed, irritating to the eyes, hold and open the container with care, do not inhale powders, avoid contact with skin and eyes, in case of insufficient ventilation, wear a breathing apparatus appropriate.

Capacity 35 GR

Composition POLYETHYLMETHACRYLATE, POLYMETHYL METHACRYLATE, BENZOYL PEROXIDE, SILICA, RED 7 / CI 15850.